nixp.ru v3.0

12 ноября 2024,
вторник,
10:11:03 MSK

Yohimbe написал 12 ноября 2006 года в 21:37 (960 просмотров) Ведет себя неопределенно; открыл 2 темы в форуме, оставил 31 комментарий на сайте.

Не получается настроить GPRS через Моторолу с650 ни в какую. Перелопатил уже кучу всяких доков, но фикушки — все оканчивается на инициализации модема. Буду рад хорошим советам!

Genie

а логи кто будет смотреть и предоставлять, а?

телепатов тут нет.

единственно, что могу предположить — это что ты не указал или указал, но неправильно строку AT+CGDCONT=1,«IP»,"<font color=«red»>APN.провайдера</font>»

anonymous
Yohimbe
все оканчивается на инициализации модема

Хм… Очнь интересненько :). У меня возможно аналогичная ситуевинка:

Использую kppp и он очнь редко сам начинает работать, останавливается вечно на инициализации модема, вышел с ситуации таким образом:

Перед нажатием Connect сначала на телефоне нажимаю кнопку «Окончание вызова/сброс/красная трубка» и следом после этого нажимаю Connect в kppp и все всегда начинает работать — попробуй, можт у нас аналогично…?!

Yohimbe

Со строкой инициализации все путем. Вывод каких команд выложить, а то я в линуксе слабоват.

Yohimbe

to denel2

У меня так не прокатывает.

Yohimbe

Вывод lsmod после подключения мобильника:

[root@localhost disconnect]# dmesg

Linux version 2.6.12-12mdksmp (apatard@n1.mandriva.com) (gcc version 4.0.1 (4.0.1-5mdk for Mandriva Linux release 2006.0)) #1 SMP Fri Sep 9 17:43:23 CEST 2005

BIOS-provided physical RAM map:

BIOS-e820: 0000000000000000 — 000000000009f800 (usable)

BIOS-e820: 000000000009f800 — 00000000000a0000 (reserved)

BIOS-e820: 00000000000f0000 — 0000000000100000 (reserved)

BIOS-e820: 0000000000100000 — 000000001bff0000 (usable)

BIOS-e820: 000000001bff0000 — 000000001bff3000 (ACPI NVS)

BIOS-e820: 000000001bff3000 — 000000001c000000 (ACPI data)

BIOS-e820: 000000001c000000 — 0000000020000000 (reserved)

BIOS-e820: 00000000f0000000 — 00000000f2000000 (reserved)

BIOS-e820: 00000000fec00000 — 0000000100000000 (reserved)

0MB HIGHMEM available.

447MB LOWMEM available.

found SMP MP-table at 000f5210

NX (Execute Disable) protection: active

On node 0 totalpages: 114672

DMA zone: 4096 pages, LIFO batch:1

Normal zone: 110576 pages, LIFO batch:31

HighMem zone: 0 pages, LIFO batch:1

DMI 2.3 present.

ACPI: RSDP (v000 GBT ) @ 0×000f6bc0

ACPI: RSDT (v001 GBT AWRDACPI 0×42302e31 AWRD 0×01010101) @ 0×1bff3000

ACPI: FADT (v001 GBT AWRDACPI 0×42302e31 AWRD 0×01010101) @ 0×1bff3040

ACPI: MCFG (v001 GBT AWRDACPI 0×42302e31 AWRD 0×01010101) @ 0×1bff7e80

ACPI: MADT (v001 GBT AWRDACPI 0×42302e31 AWRD 0×01010101) @ 0×1bff7e00

ACPI: DSDT (v001 GBT AWRDACPI 0×00001000 MSFT 0×0100000c) @ 0×00000000

ACPI: PM-Timer IO Port: 0×1008

ACPI: Local APIC address 0xfee00000

ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)

Processor #0 15:15 APIC version 16

ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)

ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])

ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])

ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])

IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23

ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)

ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)

ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)

ACPI: IRQ9 used by override.

ACPI: IRQ14 used by override.

ACPI: IRQ15 used by override.

Enabling APIC mode: Flat. Using 1 I/O APICs

Using ACPI (MADT) for SMP configuration information

Allocating PCI resources starting at 20000000 (gap: 20000000:d0000000)

Built 1 zonelists

mapped APIC to ffffd000 (fee00000)

mapped IOAPIC to ffffc000 (fec00000)

Initializing CPU#0

Kernel command line: BOOT_IMAGE=linux root=805 resume=/dev/sda8 splash=silent

bootsplash: silent mode.

PID hash table entries: 2048 (order: 11, 32768 bytes)

Detected 2339.074 MHz processor.

Using pmtmr for high-res timesource

Console: colour dummy device 80×25

Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

Memory: 448860k/458688k available (2451k kernel code, 9272k reserved, 788k data, 296k init, 0k highmem, 0k BadRAM)

Checking if this processor honours the WP bit even in supervisor mode… Ok.

Calibrating delay loop… 4620.28 BogoMIPS (lpj=2310144)

Mount-cache hash table entries: 512

CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001

CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001

CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)

CPU: L2 Cache: 512K (64 bytes/line)

CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000001

Intel machine check architecture supported.

Intel machine check reporting enabled on CPU#0.

Enabling fast FPU save and restore… done.

Enabling unmasked SIMD FPU exception support… done.

Checking 'hlt' instruction… OK.

ACPI: Looking for DSDT in initrd… not found.

CPU0: AMD Athlon(tm) 64 Processor 3000+ stepping 02

Total of 1 processors activated (4620.28 BogoMIPS).

ENABLING IO-APIC IRQs

..TIMER: vector=0×31 pin1=0 pin2=-1

Brought up 1 CPUs

CPU0 attaching sched-domain:

domain 0: span 00000001

groups: 00000001

domain 1: span 00000001

groups: 00000001

Yohimbe

checking if image is initramfs…it isn’t (no cpio magic); looks like an initrd

Freeing initrd memory: 277k freed

NET: Registered protocol family 16

PCI: PCI BIOS revision 3.00 entry at 0xfaec0, last bus=1

PCI: Using configuration type 1

mtrr: v2.0 (20020519)

ACPI: Subsystem revision 20050309

ACPI: Interpreter enabled

ACPI: Using IOAPIC for interrupt routing

ACPI: PCI Root Bridge [PCI0] (0000:00)

PCI: Probing PCI hardware (bus 00)

Boot video device is 0000:00:05.0

PCI: Transparent bridge — 0000:00:10.0

ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]

ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]

ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LNK2] (IRQs 5 *7 9 10 11 14 15)

ACPI: PCI Interrupt Link [LNK3] (IRQs *5 7 9 10 11 14 15)

ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 *11 14 15)

ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LUBA] (IRQs 5 *7 9 10 11 14 15)

ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LMAC] (IRQs *5 7 9 10 11 14 15)

ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 *10 11 14 15)

ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15)

ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 *11 14 15)

ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)

ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)

ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.

ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.

ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.

ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.

ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.

ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.

ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.

ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.

ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.

ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.

ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.

ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.

ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.

ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled.

ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.

ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.

ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.

ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.

ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.

ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.

ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.

Linux Plug and Play Support v0.97 (c) Adam Belay

pnp: PnP ACPI init

pnp: PnP ACPI: found 11 devices

PnPBIOS: Disabled

Yohimbe

PCI: Using ACPI for IRQ routing

PCI: If a device doesn’t work, try «pci=routeirq». If it helps, post a report

pnp: 00:00: ioport range 0×1000-0×107f could not be reserved

pnp: 00:00: ioport range 0×1080-0×10ff has been reserved

pnp: 00:00: ioport range 0×1400-0×147f has been reserved

pnp: 00:00: ioport range 0×1480-0×14ff could not be reserved

pnp: 00:00: ioport range 0×1800-0×187f has been reserved

pnp: 00:00: ioport range 0×1880-0×18ff has been reserved

pnp: 00:00: ioport range 0×2000-0×207f has been reserved

pnp: 00:00: ioport range 0×2080-0×20ff has been reserved

apm: BIOS version 1.2 Flags 0×07 (Driver version 1.16ac)

apm: overridden by ACPI.

audit: initializing netlink socket (disabled)

audit(1163693237.401:0): initialized

VFS: Disk quotas dquot_6.5.1

Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0×0

Initializing Cryptographic API

vesafb: framebuffer at 0xe0000000, mapped to 0xdc880000, using 6144k, total 65536k

vesafb: mode is 1024×768x16, linelength=2048, pages=1

vesafb: protected mode interface info at c000:c2d0

vesafb: scrolling: redraw

vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0

bootsplash 3.1.6-2004/03/31: looking for picture…<6>…no good signature found.

Console: switching to colour frame buffer device 128×48

fb0: VESA VGA frame buffer device

isapnp: Scanning for PnP cards…

isapnp: No Plug & Play device found

Real Time Clock Driver v1.12

PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0×60,0×64 irq 1,12

serio: i8042 AUX port at 0×60,0×64 irq 12

serio: i8042 KBD port at 0×60,0×64 irq 1

Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled

ttyS0 at I/O 0×3f8 (irq = 4) is a 16550A

ttyS0 at I/O 0×3f8 (irq = 4) is a 16550A

ttyS0 at I/O 0×3f8 (irq = 4) is a 16550A

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered

RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize

pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0

NFORCE-MCP51: chipset revision 161

NFORCE-MCP51: not 100% native mode: will probe irqs later

NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller

ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA

ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA

Probing IDE interface ide0…

hdb: _NEC DVD_RW ND-3550A, ATAPI CD/DVD-ROM drive

ide0 at 0×1f0-0×1f7,0×3f6 on irq 14

Probing IDE interface ide1…

mice: PS/2 mouse device common for all mice

md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27

NET: Registered protocol family 2

IP: routing cache hash table of 4096 buckets, 32Kbytes

TCP established hash table entries: 16384 (order: 5, 131072 bytes)

TCP bind hash table entries: 16384 (order: 5, 131072 bytes)

TCP: Hash tables configured (established 16384 bind 16384)

NET: Registered protocol family 1

ACPI wakeup devices:

HUB0 XVRA XVRB XVRC USB0 USB2 AZAD MMAC MMCI UAR1

ACPI: (supports S0 S3 S4 S5)

BIOS EDD facility v0.16 2004-Jun-25, 1 devices found

devfs_mk_dev: could not append to parent for md/0

md: Autodetecting RAID arrays.

md: autorun …

md: … autorun DONE.

RAMDISK: Compressed image found at block 0

VFS: Mounted root (ext2 filesystem).

input: AT Translated Set 2 keyboard on isa0060/serio0

SCSI subsystem initialized

libata version 1.11 loaded.

sata_nv version 0.6

ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23

ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 23

PCI: Setting latency timer of device 0000:00:0e.0 to 64

ata1: SATA max UDMA/133 cmd 0×9F0 ctl 0xBF2 bmdma 0xD800 irq 23

ata2: SATA max UDMA/133 cmd 0×970 ctl 0xB72 bmdma 0xD808 irq 23

input: ImPS/2 Generic Wheel Mouse on isa0060/serio1

ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:407f

ata1: dev 0 ATA, max UDMA/133, 312579695 sectors: lba48

ata1: dev 0 configured for UDMA/133

scsi0 : sata_nv

ata2: no device found (phy stat 00000000)

scsi1 : sata_nv

Vendor: ATA Model: WDC WD1600JS-22M Rev: 02.0

Type: Direct-Access ANSI SCSI revision: 05

ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22

Yohimbe

ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 22

PCI: Setting latency timer of device 0000:00:0f.0 to 64

ata3: SATA max UDMA/133 cmd 0×9E0 ctl 0xBE2 bmdma 0xC400 irq 22

ata4: SATA max UDMA/133 cmd 0×960 ctl 0xB62 bmdma 0xC408 irq 22

ata3: no device found (phy stat 00000000)

scsi2 : sata_nv

ata4: no device found (phy stat 00000000)

scsi3 : sata_nv

SCSI device sda: 312579695 512-byte hdwr sectors (160041 MB)

SCSI device sda: drive cache: write back

SCSI device sda: 312579695 512-byte hdwr sectors (160041 MB)

SCSI device sda: drive cache: write back

/dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 >

Attached scsi disk sda at scsi0, channel 0, id 0, lun 0

kjournald starting. Commit interval 5 seconds

EXT3-fs: mounted filesystem with ordered data mode.

Freeing unused kernel memory: 296k freed

usbcore: registered new driver usbfs

usbcore: registered new driver hub

ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)

ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21

ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 21 (level, low) -> IRQ 21

PCI: Setting latency timer of device 0000:00:0b.0 to 64

ohci_hcd 0000:00:0b.0: OHCI Host Controller

ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1

ohci_hcd 0000:00:0b.0: irq 21, io mem 0xf5108000

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 8 ports detected

ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20

ACPI: PCI Interrupt 0000:00:0b.1 -> Link [APCL] -> GSI 20 (level, low) -> IRQ 20

PCI: Setting latency timer of device 0000:00:0b.1 to 64

ehci_hcd 0000:00:0b.1: EHCI Host Controller

ehci_hcd 0000:00:0b.1: debug port 1

ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2

ehci_hcd 0000:00:0b.1: irq 20, io mem 0xf5104000

PCI: cache line size of 64 is not supported by device 0000:00:0b.1

ehci_hcd 0000:00:0b.1: park 0

ehci_hcd 0000:00:0b.1: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 8 ports detected

ts: Compaq touchscreen protocol output

EXT3 FS on sda5, internal journal

Adding 1004020k swap on /dev/sda8. Priority:-1 extents:1

ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17

ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17

drivers/media/dvb/b2c2/skystar2.c: FlexCopIIB(rev.195) chip found

drivers/media/dvb/b2c2/skystar2.c: the chip has 38 hardware filters

driver_initialize MAC address = 00:d0:d7:10:b0:f7:00:00

DVB: registering new adapter (SkyStar2).

i2c_readbytes: i2c read error (addr 0a, err == -121)

DVB: registering frontend 0 (ST STV0299 DVB-S)…

Linux agpgart interface v0.101 (c) Dave Jones

kjournald starting. Commit interval 5 seconds

EXT3 FS on sda9, internal journal

EXT3-fs: mounted filesystem with ordered data mode.

Supermount version 2.0.4 for kernel 2.6

ntfs: Ignoring new-style parameters in presence of obsolete ones

NTFS driver 2.1.22 [Flags: R/O DEBUG MODULE].

NTFS volume version 3.1.

loop: loaded (max 8 devices)

ieee1394: Initialized config rom entry `ip1394\′

ohci1394: $Rev: 1250 $ Ben Collins

ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18

ACPI: PCI Interrupt 0000:01:0e.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18

PCI: Via IRQ fixup for 0000:01:0e.0, from 5 to 2

ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[18] MMIO=[f5010000-f50107ff] Max Packet=[2048]

hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)

Uniform CD-ROM driver Revision: 3.20

ACPI: Power Button (FF) [PWRF]

Floppy drive(s): fd0 is 1.44M

FDC 0 is a post-1991 82077

ieee1394: Host added: ID:BUS[0-00:1023] GUID[00001485003fd4cd]

eth1394: $Rev: 1247 $ Ben Collins

eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)

NET: Registered protocol family 17

NET: Registered protocol family 10

Disabled Privacy Extensions on device c03efce0(lo)

IPv6 over IPv4 tunneling driver

ohci_hcd 0000:00:0b.0: wakeup

usb 1-4: new full speed USB device using ohci_hcd and address 2

usb 1-4: device not accepting address 2, error -110

usb 1-4: new full speed USB device using ohci_hcd and address 3

Yohimbe

Вывод lsmod:

[root@localhost disconnect]# lsmod

Module Size Used by

md5 4576 1

ipv6 247936 6

raw 7648 1

snd_pcm 83812 0

snd_timer 22596 1 snd_pcm

snd_page_alloc 9384 1 snd_pcm

snd 48644 2 snd_pcm,snd_timer

soundcore 8256 1 snd

af_packet 19272 0

eth1394 18536 0

floppy 57108 0

video 15076 0

thermal 11944 0

tc1100_wmi 6084 0

processor 19560 1 thermal

fan 4164 0

container 4000 0

button 5840 0

battery 8452 0

ac 4260 0

ide_cd 39172 0

ohci1394 34068 0

ieee1394 291832 2 eth1394,ohci1394

loop 16072 0

ntfs 215448 1

nls_koi8_u 5760 3

nls_cp866 5760 2

vfat 11840 2

fat 47676 1 vfat

supermount 33552 1

amd64_agp 10952 0

agpgart 30252 1 amd64_agp

skystar2 29316 0

dvb_core 78152 1 skystar2

mt352 7012 1 skystar2

stv0299 11624 1 skystar2

nxt2002 9700 1 skystar2

firmware_class 8544 2 skystar2,nxt2002

mt312 8644 1 skystar2

i2c_core 18656 5 skystar2,mt352,stv0299,nxt2002,mt312

tsdev 7008 0

ehci_hcd 31048 0

ohci_hcd 20772 0

usbcore 111612 3 ehci_hcd,ohci_hcd

evdev 8672 0

ext3 127784 2

jbd 54360 1 ext3

sd_mod 17280 7

sata_nv 7012 6

libata 43268 1 sata_nv

scsi_mod 123560 2

Yohimbe

Выложил все, что знал!

Genie
ohci_hcd 0000:00:0b.0: wakeup

usb 1-4: new full speed USB device using ohci_hcd and address 2

usb 1-4: device not accepting address 2, error -110

usb 1-4: new full speed USB device using ohci_hcd and address 3

как0то оно у тебя не очень определяется, да и модуль не грузит

так что давай, лучше распиши, что у тебя есьт, что конкретно делаешь и что появляется в логах, /var/log/messages, к примеру

Yohimbe

Делаю я вот это:

mknod /dev/ttyACM0 c 166 0

ln -s /dev/ttyACM0 /dev/modem

Потом настраиваю в KPPP.

Yohimbe

Лог /var/log/messages залил сюда http://slil.ru/23425503 , а то большой очень, чтобы сюда выкладывать.

palp

хм.. странно у тебя в messages

Nov 18 13:26:13 localhost kernel: No module symbols loaded — kernel modules not enabled.

Yohimbe

И чтобы это значило? :)

Yohimbe

И все таки… кто-нибудь поможет???

Genie

eto znachit, chto yadro u tebya ne umeet gruzit' moduli

ty eo sam sobiral?

esli da, to soberi zanovo

esche problema byvaet iz-za togo, chto skripty soedineniya delautsya v vindah i potomu imeut nepravil’nye okonchaniya strok

Yohimbe

Всем спасибо. Соединение настроил.

fly4life
Yohimbe
Всем спасибо. Соединение настроил.

Дык, поделись секретом, в чём была проблема? ;).

Последние комментарии

ecobeingecobeing.ru
Экология и вегетарианство на благо всем живым существам Планеты.