сетевуха Marvell Yukon, постоянно лаги 0

У меня какая-то проблема с сетью (выкидывает из gaim, и инет лагает), не знаю что сделать.

При выполнении команды #dmesg

sk98lin: Network Device Driver v8.28.1.3
(C)Copyright 1999-2005 Marvell(R).
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: Marvell Yukon 88E8053 Gigabit Ethernet Controller
      PrefPort:A  RlmtMode:Check Link State
ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
  http://www.scyld.com/network/ne2k-pci.html
ACPI: PCI Interrupt 0000:01:09.0[A] -> GSI 17 (level, low) -> IRQ 177
eth1: Compex RL2000 found at 0xb800, IRQ 177, 00:80:48:FD:F8:2E.

skiped

SELinux: initialized (dev sda3, type ntfs), uses genfs_contexts
Adding 1020116k swap on /dev/sda2.  Priority:-1 extents:1 across:1020116k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
eth0: network connection up using port A
    speed:           100
    autonegotiation: yes
    duplex mode:     full
    flowctrl:        none
    irq moderation:  disabled
    tcp offload:     enabled
    scatter-gather:  enabled
    tx-checksum:     enabled
    rx-checksum:     enabled
    rx-polling:      enabled
audit(1133439299.933:2): avc:  denied  { write } for  pid=1957 comm="dhclient-script" name="resolv.conf" dev=sda1 ino=3951999 scontext=system_u:system_r:dhcpc_t tcontext=root:object_r:etc_t tclass=file
audit(1133439299.933:3): avc:  denied  { write } for  pid=1957 comm="dhclient-script" name="resolv.conf" dev=sda1 ino=3951999 scontext=system_u:system_r:dhcpc_t tcontext=root:object_r:etc_t tclass=file
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.7
NET: Registered protocol family 31

skiped

parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (interrupt-driven).
lp0: console ready
eth0: no IPv6 routers present
eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.
...

много раз повторяется строчка: eth0: SkYuk2RestartRxBmu failed.

...
eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.
usb 1-1: new high speed USB device using ehci_hcd and address 2
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2

usb-storage: device scan complete
SELinux: initialized (dev sdb1, type vfat), uses genfs_contexts
usb 1-1: USB disconnect, address 2
eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.
...

опять строчка повторяется

eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.
usb 1-1: USB disconnect, address 3
usb 1-1: new high speed USB device using ehci_hcd and address 4
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning

eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.
eth0: network connection up using port A
    speed:           100
    autonegotiation: yes
    duplex mode:     full
    flowctrl:        none
    irq moderation:  disabled
    tcp offload:     enabled
    scatter-gather:  enabled
    tx-checksum:     enabled
    rx-checksum:     enabled
    rx-polling:      enabled
eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.
eth0: SkYuk2RestartRxBmu failed.

и так до конца